Axminster TSCE-12R Manuál s instrukcemi

Code 700158Code 600807TSCE-12R 305mmTable Saw

Contents of warning labels- 10 -

Shipping ContentsUnpackingRemove box and wood crating completely from around saw. Check for shipping damage immediately to your distrib

Model TSCE-12RCode 600087Rating IndustrialPower 3.75kW (415V)Blade Dia/Bore 305mm/30mmBlade Tilt 0° - 45°Max Depth of Cut @ 45˚ 72mmMax Depth o

Foundation Drawing TSCE-305R2235mm625mm1400mm640mm898mm800mm650mm- 13 -

- 14 -

AssemblyMotor Cover Assembly˙Tool: 6mm Allen Hex Wrench 1.Remove motor cover A (Figure 1) insert on cabinet.2.Closing the motor cover and fasten cover

Extension WingReferring to Figures 4 and 5:Hardware: (6)7/16”*1-1/2” Hex Cap Bolts, (6)7/16” Lock Washers, (6) 7/16” Flat Washers & (2) Exten

Riving Knife Installation Description Referring to Figure 7:The complete riving knife and guard assembly is shown in Figure.7Installation Referring to

Mounting Rip Fence Support BracketAdjust the rip fence support Bracket flush with the Table by turning four set screw A (Figure.9) and using a

Mounting Front Guide Bar1.Mounting the Front Guide Bar A (Figure12) to the front of the saw Table B (Figure12).2.See the Rip Fence Alig

List of Contents1. General Information ...22. Safety Rules...

Sliding Table Setting & Installation-OptionIf the cross cut table is not set parallel to the saw blade this causes heeling; that is ; the blade i

Roll the table through its full travel, checking that the gap remains the same all the way along the table. If the gap varies from one end to the othe

Riving Knife AdjustmentLateral alignmentThe saw blade and riving knife must be in line as close as possible with each other (lateral alignment)

4. Tighten the socket head flat screws (E).5. Reinsert the riving knife; tighten the lock handle (A, Fig. 17) and check that the saw bla

Adjusting 45° and 90° Positive StopsThe stops have been adjusted at the factory. After a period of use, or, after moving the saw to another loc

Make all machine adjustments or maintenance with the machine unplugged from the power source. Failure to comply may cause serious injury!Referring to

TroubleshootingTroublePossible CauseSolutionSaw stops or will not startDoes not make accurate 45° or 90°cutsMaterial binds blade when rippingSaw makes

- 27 -

Table and Cabinet Assembly(Right tilt)lndex Part Description Size Qty.No. No.1………… UOTS10-1…………….…… Lock Knob………………. ……………... .…12………… UOTS10-2.………………

Table and Cabinet Assembly(Right tilt)lndex Part Description Size Qty.No. No.28……….. UOTS10-28…..……………. Tilt Scale…………………… ……………... .…129……….. UOTS10-

ADDITIONAL MARKINGS 1. The following warning also appears on the tool and in the Instruction Manual per UL987.WARNING: FOR YOUR OWN SAFETY READ INST

Table and Cabinet Assembly(Right tilt)lndex Part Description Size Qty.No. No.54……….. 901M06016…………………. Hex Socket Head Screw.….M6ǘǘ16……...…255……….. 9

Motor and Trunnion Assembly- 31 -

Motor and Trunnion Assembly- 32 -

Motor and Trunnion Assembly- 33 -

Motor and Trunnion Assembly- 34 -

Motor and Trunnion Assembly- 35 -

Blade Guard Assembly- 36 -

Blade Guard Assembly- 37 -

- 38 -

Rip Fence Assemblylndex Part Description Size Qty.No. No.1………... 231-1111……………………… Rip Fence Bracket……… …………….. .…12………... 231-1112……………………… Clamping

7. DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.8. USE RIGHT TOOL. Don't force tool or attach

Rip Fence Assemblylndex Part Description Size Qty.No. No.34……….. 231-11134……………………. Stop Profile……………… …………… ….135……….. 231-11135……………………. Sticker…………

- 41 -

Sliding Table System Assembly (UST-36)Index Part Description Size Qty.No. No.1………… UST-36-01………………… Hex Socket Cap Screw… 3/8”x1”…... .…22………… UST-36

Sliding Table System Assembly (UST-36)Index Part Description Size Qty.No. No.34……….. UST-36-34………………… Round Head Screw………... M4x10…….. .…235……….. UST-

- 44 -

- 45 -

Axminster Tool Centre,Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PHaxminster.co.ukPlease dispose of packaging for the product in a responsible ma

2. Safety RulesWarnings1. Read and understand the entire owner's manual before attempting assembly or operation.2. Read and understan

Warnings16. Provide for adequate space surrounding work area and non-glare, overhead lighting.17. Keep the floor around the machine clean and

Warnings35. Ground all machines.It should make sure the “PE”terminal being connection before machine operating.36. Don't use in dangerous environ

enable the user of the machine to make a better evaluation of the hazard and risk. 47. After switching off the saw motor, allow the sawblade to stop f

b) Selection of sawblade and riving knife: The operator should only select sawblade of a dismeter and thickness suitable for the machine, a